M10 Loose Bolt High Tensile 8.8 Masonry Shield Anchor Zinc
M10 Loose Bolt High Tensile 8.8 Masonry Shield Anchor Zinc
£5.93
Out of Stock
£5.93
Add to Cart
Starts from: £100
Ships within 8 hours (on average).
Ships within 8 hours (on average).
Free Shipping RM48 (2-3 days if ordered before 2pm)
Upgrades available at checkout (e.g. tracked service and courier for time sensitive deliveries)
Call: 01242 522244
Email: sam@fixaball.co.uk
Website: www.fixaball.co.uk
for technical and sales queries
Share this:
About this product :
M10, 10mm Diameter Threaded, Hex Head, Loose Bolt with Masonry Shield, Heavy Duty Masonry Anchor Fixing, High Tensile (8,8), Zinc, ZYP
Fixaballsells all lengths of M10 Loose Hex Bolt, Heavy Duty Masonry Anchors.
Optimising your fixings holding capacity.
Clean the hole using an appropriate sized brush
Installation Temp is 0°: make sure water does not seep into the hole. The expansion water to ice could crack the concrete. Under wet conditions, use a specified injection resin.
Introduce the anchor through the material to be fixed into the hole up to the embedment depth, according to the values on the table. Use a hammer to ensure the required depth. Do not apply any intermediate layer between the material to be fixed and the washer, such as sealing products.
Apply the specified torque with a torque wrench.
In the case the holes on the material to be fixed have a bigger diameter than required, it is necessary to insert a thicker washer and of a bigger diameter. But please, note that this procedure does not ensure a correct distribution of shear loads amongst all the anchors of a same group, and this shear load is applied only to the anchors with a correct diameter on the material to be fixed.
Orders placed before 2pm are dispatchedsame day (Mon-Fri).
Standard, is Royal Mail, 2nd Class (2-5 days, most likely 2 days). For a er delivery time, select 1st class or courier at checkout.
Please make your size and pack quantity selection from the drop down menus.
Important Loose Bolt Anchor Performance Dimensions
Thread Diameter of Hex Bolt
Shield Hole Size
Max Fix.Thickness
M10
16mm
10mm
M10
16mm
25mm
M10
16mm
50mm
M10
16mm
75mm
NOTE: the1stdimension refers to the thread diameter and not the hole diameter. Please see the table below for further information on what masonry drill bit to use. The2nddimension refers to the maximum fixture thickness (space between the underside of the head and the shield +/- 5mm). The3rddimension is the actual length of the hex-bolt/ hex-set that goes into the sheild (in brackets).
Installation of Shield Anchors
When drilling holes you must respect the specified minimum depth and diameters shown in the table below. Holes must be square to the surface of the base material (e.g concrete) for safety during installation and to optimise holding capacity. Use the material/ fixture as a template to dill accurate locations.
If drilling through concrete that has rebar reinforcements, special care must be taken to avoid damaging them. If some rebar is encountered, abort the hole, repair with high quality mortar and create a hole, no less than twice the diameter of the shield anchor, away.
Table: Shows typical masonry shield values and measurements
All measurements in Metric - mm (all lengths are taken from under the hexagan head)
Thread Diameter
Hole Diameter
Hole Depth
Fixture/ Material Clearance Hole
Centre Spacing Between Holes
Minimum Distance From Edge of Material
Tensile/ Pull Load
k/N (tonnes)
Shear Load k/N (tonnes)
Torque to tighten Nm
M10
16
65
11 – 12
180
120
6.2
6.1
27
All specifications are true with correct installation
